FRSKY S6R INSTRUCTION MANUAL Pdf Download (2024)

Instruction Manual for FrSky S6R/S8R

Overview

S T A B I L I Z A T I O N

Working State

Green LED

Red LED

Status

Yellow LED

Flashing

Binding

Accelerometer outside of Calibration limits[0.9 G , 1.1 G]

Flashing

OFF

Normal

OFF

Accelerometer within Calibration limits [0.9 G , 1.1 G]

Flashing

Completed accelerometer calibration

OFF

Flashing

Signal lost

Specifications

•

Model name: S6R (6CH receiver with built-in 3-axis gyro and 3-axis acceleration)

47.42×23.84×14.7mmmm (L × W × H)

S8R (8CH/16CH receiver with built-in 3-axis gyro and 3-axis acceleration)

46.47×26.78×14.12mmmm (L × W × H)

•

Weight: S6R 12.1g ; S8R 14g

•

Number of Channels: S6R 6CH (1~6CH from conventional channel outputs)

S8R 16CH (1~8ch from conventional channel outputs, 1~16ch from SBUS port)

•

Operating Current: S6R 100mA@5V ; S8R 120mA@5V

•

With RSSI PWM output on board (S8R only)：PWM voltage output(0~3.3V)，100HZ，1500±500us

•

Operating Voltage Range: 4.0~10V

•

Operating Range: full range

•

Gyroscope Measurement Range: ±2000dps

•

Accelerometer Measurement Range: ±4g

•

Firmware Upgradeable

•

Compatibility: ACCST D16

Features

• Built-in three-axis gyroscope and three-axis accelerometer sensor module

• Built-in RSSI PWM output (0~3.3V) (S8R only)

• Built-in battery voltage detection.

• Smart Port enabled

Channels

Number of

Corresponding parts

Full name

channel

on the model

CH1

AIL 1

Aileron

CH2

ELE 1

Elevator

CH3

THR

Throttle

CH4

RUD

Rudder

Aileron

CH5

AIL 2

CH6

ELE 2

Elevator

FrSky Electronic Co., Ltd.

www.frsky-rc.com

Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com

Instruction Manual for FrSky S6R/S8R

Conventional model

Layout

The available flight modes can be assigned to CH10 and CH11 with three-position switches.

Flight mode

Stabilization

Automatic level

CH10>M+H

CH10 (3 pos SW)

(CH10 SW Down)

M-H<CH11<M+H

CH11>M+H

CH11(3 pos SW)

(CH11 SW Mid)

(CH11 SW Down)

Delta wing & Flying wing & V-tail

Layout of Delta wing / Flying wing

The available flight modes can be assigned to CH10 with a three-position switch.

Flight mode

Stabilization

CH10>M+H

CH10

(CH10 SW Down)

When Delta wing/Flying wing/V-tail is selected, the signal produced by the transmitter should be without active mixes on the channels related to AIL

and ELE. S6R/S8R will mix the AIL(CH1) and ELE(CH2) input signal with a fixed mix percentage automatically. Signals on CH4~CH8 will behave

as required by the user.

represents a neutral signal period (1500μs)

represents the time of required signal change to activate the mode (50μs). When the factory settings are selected, the switch position shown

above represents the required modes.

Flight mode:

Off:

When the mode is activated, S6R/S8R will transmit the received commands produced by the transmitter to the model without compensating.

Stabilization:

When the model is activated, S6R/S8R will compensate with external forces (wind) as soon as receiving commands from the

transmitter. This function is used to enhance the stability of the model on three axes (Pitch, Roll, Roll). CH9 could be used to adjust gyro gain by

assigning a knob or a slider, changing the sensitivity of the counteracting signal produced by the internal three-asis gyroscope.

Automatic level:

When the mode is activated, S6R/S8R will make the model return to level orientation with internal three-axis accelerometer and

three-axis gyroscope on AIL and ELE channels after the sticks being released to neutral. RUD channel works in stabilization mode only.

Hover:

When the mode is activated, S6R/S8R will make the nose of the model straight up with internal three-axis accelerometer and three-axis

gyroscope on RUD and ELE channels (ELE and RUD inputs are not required). Under this mode, AIL is used to control the rotation of the model and

THR adjust the altitude. AIL channel works in stabilization mode only.

Knife-egde mode:

When the mode is activated, S6R/S8R will roll the plane on a certain side (wing points up) with internal three-axis accelerometer

and three-axis gyroscope on RUD and AIL channels.Thus, AIL inputs are not required. While the mode steering is done with ELE, altitude will be

maintained with THR/RUD. ELE channel operates in stabilization mode only.

FrSky Electronic Co., Ltd.

www.frsky-rc.com

Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com

Smart Port

Outputs

Status

Blue LED

Self-check in progress

OFF

Completed self-check

Number of

Corresponding parts

Full name

channel

on the model

CH7

User-defined

CH8

User-defined

Gyro gain adjustment

CH9

No mark

CH10&CH11

No mark

Flight modes

CH12

Self-check activation switch

01140055

Hover

Knife-Edge

CH10>M+H

CH10<M-H

(CH10 SW Down)

(CH10 SW Up)

CH10 SW-mid

CH11<M-H

M-H<CH11<M+H

(CH11 SW Up)

(CH11 SW Mid)

Layout of V-tail

Auto Level

Off

CH10<M-H

CH10 SW-mid

(CH10 SW Up)

01140055

Version

1.0

Gyro gain adjustment of CH9: When the the value of CH9 is in the center, the gain is zero. The gain increases as the value gets bigger. Until the

value is ±100%, the gain reaches maximum.

Note: CH9~CH12 are not marked on the diagram.

CH9 Edit — Setting CH9 at Weight 50 and offsetting 50, the assigned pot/slider will work normally.

Attentions

CH1~CH8 should be connected to the corresponding servos.

S.Port could be used to update, edit parameter settings via FrSky STK PC tool and connect with telemetry sensors.

Binding Procedure

Binding is the process of uniquely associating a particular receiver to a transmiter/transmitter module. A transmiter/transmitter module can be bound

to multiple receivers (not to be used simultaneously). A receiver can only be bound to one transmiter/transmitter module.

Follow the steps below to finish the binding procedure.

1、 Put the transmitter/transmitter module into binding mode

1.1 For Taranis X9D Plus 2019 as an example,turn on the radio, go to the MENU – MODEL SETUP – PAGE 2, choose Internal or External RF,

choose the [mode] ACCST D16 and select BIND.

1.2 For Horus X10 Express as an example,turn on the radio, go to the MDL – INT MODULE or EXT MODULE, choose the [TX RF Protocol] ACCST

D16 and select BIND.

1.3 For transmitter module (XJT as an example), turn on the transmitter while holding the FS button on the module, release the button and the RED

LED on XJT module flash.

2、 Connect the battery to the receiver while holding the F/S button on the receiver. The RED LED on the receiver will flash, indicating the binding

process is completed.

Status

3、 Turn off both the transmitter and the receiver.

4、 Turn on the transmitter and connect the battery. The GREEN LED on the receiver indicates the receiver is receiving commands from the

transmitter. The receiver/transmitter module binding will not have to be repeated, unless one of the two is replaced.

Note: After binding procedure is completed, recycle the power and check if the receiver is really under control by linked transmitter.

Set up your model and receiver step by step

You need complete calibration of Accelerometer about the six positions via the S6R/S8R.Lua/FreeLink APP/FreeLink.exe firstly.

Step1: Connect your servos follow the channel list according to your model.

Step2: Set you radio follow the channel list.

Step3: Choose the Wing Type via the configuration tool (S6R/S8R.Lua/FreeLink APP/FreeLink.exe).

Step4: Choose the AUTO LEVEL mode, check the model servo feedback.

Step5: Choose the manual mode, check servo feedback via transmitter.

Quick Mode

It supports stabilization mode and manual (six-axis off) mode and configured through CH10. What's more, an urgent mode is added to configure

automatic level mode default through CH12. The precise configuration is written below.

Channel

Position

SW Down

CH10

SW Mid

SW Up

CH12

SW Down

Note: The default mode of S6R/S8R is Quick Mode.When re-flashing firmware of S6R/S8R or replacing with a new one, the preset

mode will be cleared out.

- If Quick mode is applied, there is no Knife Edge or (3D) Hover mode.

- CH11 is not used when using Quick Mode.

Modes

Conventional Model

The model types could be enabled via Freelink.exe or S6R/S8R.Lua. If required, S6R/S8R could be used as a standard 6/8 channel receiver.

Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com

Version

1.0

Configuration

Methods: APP configuration

FrSky radio configuration

PC configuration software (FrSky STK usb updater)

Configuration parameters: Wing type, mounting type, gain setting, offset angle setting, accelerometer calibration.

APP(IOS/Android) configuration：

•

Connect the S6R/S8R to the App with AirLink S.

The menu screen on the home page is displayed below:

Off

You can download the APP.

IOS FreeLink APP

FrSky radio configuration:

•

Copy the S6R/S8R.Lua files on the SD card of the transmitter

•

Bind the S6R/S8R to the transmitter and run the files.

PC configuration software:

•

Connect S6R/S8R as shown below to the FrSky STK usb adapter, and plug it into PC

•

Run the S6R/S8R Freelink.exe and access the home page.

•

Press open to connect with S6R/S8R.

RED LED

Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com

Instruction Manual for FrSky S6R/S8R

Flight Mode

None

Stabilization Mode

Automatical Level Mode

Urgent Mode (Automatic Level Mode)

Stabilization

Delta Wing

Automatic level

stabilization

Flying Wing

automatic level

Hover

V-tail

Knife-edge

FrSky Electronic Co., Ltd.

www.frsky-rc.com

01140055

Instruction Manual for FrSky S6R/S8R

Android FreeLink APP

DIP

GREEN LED

FrSky Electronic Co., Ltd.

www.frsky-rc.com

01140055

Version

1.0

Version

1.0

S T A B I L I Z A T I O N